| specifications︰ | Name of product Antifoaming Agent Y – 330
Quality Features Distinction of single/mixture : Mixture
Ingredients and content :
Glycerol monosterate 31566-31-1 23.00 %
Sodium alginate 9005-38-3 37.00 %
Water 40.00 %
Noxious Hazard
Classification Classification Category: chemical with corrosive property with other hazardous characteristics
Danger: If heated and dehydrated, becomes flammable liquid
Noxious character: Irritates skin and mucous membrane, and may cause inflammation.
Danger: the Fire Service Act –4 th class No 3 type of dangerous substance , water – soluble.
Environmental influence : No Data
Emergency Procedures Contact with eyes: Wash thoroughly with plenty of water for 10 ~ 15 minutes and immediately consult doctor for treatment.
Contact with skin: Take off cloth, shoes, etc immediately and wash off the contacted area with plenty of flowing water. If external portion of skin shows visible changes or pain persists, consult doctor.
Inhaled: If inhaled in large quantity, immediately transfer the victim to well aerated area with fresh air and consult doctor.
Consumed: Wash off the mouth with water. If conscious, feed water and induce vomiting by inserting fingers into throat. If the victim is unconscious, refrain from inducing vomiting and consult doctor immediately.
Measures in the event of fire Method of extinguishers : Powder , carbonic acid gas , Dry sand
Extinguisher : Extinguishers , Dry sand
Exposure Prevention Measures Permissible concentration : No standard
Permissible standard : Recommendation of ACGIH in USA – No standard
Install facilities such as safety shower, drain board, washing facilities as deemed necessary at the locations where the chemical is handled.
Protective gears: Wear safety goggle, rubber gloves, rubber boots, gas mask and rubber apron whenever necessary.
Physica/
Chemical
Properties Appearance : Muddy white solution
Specific gravity : 0.95 ~ 1.05/25 ℃
Solubility : Water dispersive
Flammability : None
Viscosity : 300 cp/25 ℃
Hazardous Matter Information The flash point : 175 ℃
Ignition point : None
The flash limit : None
Stability : Stable under normal handling
Hazard Information Oral Poison : LD 508 g/Kg ( Oral Lot )
Carcinogenic : No data
Environmental information No report regarding poison to marine life
Precautions in discarding Discard small amount or put into incinerator
Precautions in Transportation Take caution to prevent leakage from the container.
Prepare neutralizer and dry sand.
Applicable Rules and Regulations The Fire Service Act –4 th class No 3 type of dangerous substance , water – soluble.
Reference literature 1) Permissible concentration recommendation of Japan Industrial sanitary (1992)
2) IARC
3) Manual of dangerous and poisonous substances processing treatment
– overseas technology data institute ( 1974)
4) Chemical poison to fishes and marine life ( 1978)
This MSDS has been prepared on the basis of generally obtainable literature and data held at the company.
In particular, toxicity Data illustrates information on toxicity of harmful chemical substance when present in itself. As such these data may be in disparity with the toxicity of this product.
This MSDS conveys basic information for handling of the product and should not be considered as safety assurance.
As such, this MSDS does not stipulate responsibility nor assurance for any accidents that may arise in handling and storage of the product, as illustrated above.
Since the data provided by this MSDS is not complete, please take sufficient precautions in handling and storage of the product. |
| Advantages︰ | 1) Features
a) Outstanding chemical resistance.
b) Outstanding foam suppression and anti-foaming effect with minute quantity.
c) Outstanding continuity of its effect without requiring complicate addition of the agent.
d) Excellent dispersion character in water, allowing it to be diluted in water in application.
e) High wash ability ensures absence of remnant of the agent on the board.
|
| Min Order︰ | 20 litre |
| Ship Date︰ | 2 weeks |
|
|
Anti-foaming agent Y –330 has foam suppression and anti-foaming effects for foams generated in various processes such as development in manufacturing of printed circuit board, resist stripping and etching .
|
|
|
|
|
